Standard product information
Peripheral Equipment
EZ Series
Illuminated Switch
Global Code
Product Features
USB2.0 (Powered from USB bus)
Rated Input Voltage: 5VDC (powered from USB bus)
Power Consumption: 2.0W max
Surrounding Air Temperature: 0 to 55º C (32 to 131º F)
Supported Software: GP-Pro EX Ver. 3.1 or later (GP4000, GP4000M)
GP-Pro EX Ver. 3.12 or later (LT4000M)
GP-Pro EX Ver. 4.0 or later (SP5000, WinGP)
Storage Temperature: -25 to 70 deg C (-13 to 158 deg F)
Environmental Ratings: IP65f front face/IP20 back
Certifications: CE. CSA, UL, RoHS

General Specifications

Supported Standards and Regulations ul_508.gif   ul_508_ansi.gif   safetymark_ce.gif   safetymark_kc.gif   safetymark_ctick.gif   safetymark_gostr.gif  
Supported Software GP-Pro EX Ver. 3.1 or later (GP4000, GP4000M)
GP-Pro EX Ver. 3.12 or later (LT4000M)
GP-Pro EX Ver. 4.0 or later (SP5000, WinGP)

Functional Specifications

Number of Switches 5 illuminated switches
Durability of Switches 1 million times or more for each switch
LED Colors Red, Green, Yellow, Blue, White, Orange
Insert Label Printable and replaceable insert labels

Electrical Specifications

Power Supply *1
Rated Input Voltage 5 Vdc (Powered from USB bus)
Input Voltage Limits 4.75 to 5.25 Vdc
Power Consumption *2 2.0 W or less

*1 When you connect with GP4000M Series, please connect via self power USB Hub.

*2 If connecting to a display unit that has a USB I/F with an output current of less than 500 mA, be sure to supply power from an external source (such as a self-powered hub) to EZ Illuminated Switch because the display unit cannot supply enough power.

Environmental Specifications

Physical Environment
Surrounding Air Operating Temperature 0 to 55 ℃ (32 to 131 ℉)
Storage Temperature -20 to 60 ℃ (-4 to 140 ℉)
Surrounding Air and Storage Humidity 10 to 90% RH (Non-condensing, wet bulb temperature 39 ℃ [102.2 ℉] or less)
Dust 0.1 mg/m3 (10-7 oz/ft3) or less (nonconductive levels)
Pollution Degree For use in Pollution Degree 2 environment
Corrosive Gasses Free of corrosive gas
Operating Altitude 2,000m [6,561 ft] or lower
Mechanical Environment
Vibration Resistance IEC/EN 61131-2 compliant
5 to 9 Hz Single amplitude 3.5 mm (0.14 in.)
9 to 150 Hz Fixed acceleration: 9.8 m/s2
X, Y, Z directions for 10 cycles (100 min.)
Concussion Resistance IEC/EN 61131-2 compliant
(147 m/s2, X, Y, Z directions for 3 times)
Electrical Environment
Electrostatic Fast Transient Burst IEC61000-4-4
2 kV Power Port (Display Unit)
1 kV Signal Ports
Electrostatic Discharge Immunity IEC/EN61000-4-2
6 kV Contact Discharge
8 kV Air Discharge

External Specifications

Connector Type USB I/F: Type B (socket), USB 2.0 Full Speed
USB Cable Length 1m (Removable)
External Dimensions W122 x H54 x D28 mm (W4.80 x H2.13 x D1.10 in.)
Structure *3 IP65 NEMA #250 TYPE 4X/13
(on the front panel when properly installed in an enclosure)
Weight 110 g (0.24 lb) or less

*3 The front face of the unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the unit's level of resistance is equivalent to these standards, oils that should have no effect on the unit can possibly harm the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the panel for long periods of time. If the unit's front face protection sheet peels off, these conditions can lead to the ingress of oil into the unit and separate protection measures are suggested. Also, if non-approved oils are present, they may cause deformation or corrosion of the front panel's plastic cover. Therefore, prior to installing the unit, be sure to confirm the type of conditions that will be present in the unit's operating environment. If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of protection cannot be kept. To maintain the original protection level, be sure to replace the installation gasket regularly.

The upper surface of the gasket should protrude approximately 2.5 mm (0.1 in.) from the groove. Check the gasket is inserted correctly before installing this unit to a panel.

A gasket with scratches or dirt could have lost much of its water resistance. It is recommended that the gasket should be changed periodically (e.g. once a year, or as soon as scratches or dirt become visible) for water resistance equivalent to IP65.