Standard product information
SP5000 Series
Global Code
Product Features
12" DC Wireless LAN Auto Scaling Brightness Sensor (Premium Display)
Repair Status
✔ (Maintenance service is available, able to be maintained.)
End of sales
To be confirmed
End of repair
To be confirmed
Replacement option 1
To be confirmed
Please contact your [local Pro-face office]

Display specifications
Display type
Display size
1,024 x 768 pixels (XGA)
Auto scaling
Effective display area
W245.76 x H184.32 mm [W9.68 x H7.26 in.]
Display colors
16 million colors
White LED (Not user replaceable. When replacement is required, contact your local distributor.)
Backlight service life
50,000 hrs. or more (each in continuous operation at 25 °C [77 °F] before backlight brightness decreases to 50%)
Brightness control
0 to 100 (Adjusted with touch panel or software)
Brightness sensor
Touch panel type
Resistive Film (analog, multi-touch)
Touch panel resolution
1,024 x 1,024
Touch panel lifetime
1,000,000 times or more
Electrical specifications
Rated input voltage
12 to 24 Vdc
Input voltage limits
10.8 to 28.8 Vdc
Allowable voltage drop
12 Vdc: 1.25 ms or less
24 Vdc: 5 ms or less
Power consumption
Max. 23 W
When power is not supplied to external devices: 20 W or less
Backlight adjusted (20%): 13 W or less
Backlight OFF (Stand-by mode): 8 W or less
In-rush current
30 A or less
Noise immunity
Noise Voltage : 1,000 Vp-p
Pulse Duration : 1 µs
Rise Time : 1 ns
(via noise simulator)
Voltage endurance
1,000 Vac, 20 mA for 1 minute (between power terminal and FG terminals)
Insulation resistance
500 Vdc, 10 MΩ or more (between power terminal and FG terminals)

1Power consumption for Display Module only

Environmental specifications
International safety standards
CE, UKCA, UL,cUL (508) Listed, ANSI/CSA (UL508+1604) Listed, CCC, KCs, NEPSI, KC
Surrounding air temperature
0 to 60 °C [32 to 140 °F]
Storage temperature
-20 to +60 °C [-4 to 140 °F]
Ambient humidity
10 to 90 % RH (Wet bulb temperature: 39 °C [102.2 °F] max. - no condensation)
Storage humidity
10 to 90 % RH (Wet bulb temperature: 39 °C [102.2 °F] max. - no condensation)
0.1 mg/m3 (10-7 oz/ft3) or less (non-conductive levels)
Pollution degree
For use in Pollution Degree 2 environment
Corrosive gases
Free of corrosive gases
Air pressure (altitude range)
800 to 1,114 hPa (2,000 m [6,561 ft.] above sea level or less)
Vibration resistance
IEC/EN 61131-2 compliant
5 to 9 Hz single amplitude 3.5 mm [0.14 in.]
9 to 150 Hz fixed acceleration: 9.8 m/s2
X, Y, Z directions for 10 cycles (approx. 100 min.)
Concussion resistance
IEC/EN 61131-2 compliant 147 m/s2, X, Y, Z directions for 3 times
Electrostatic discharge immunity
Contact Discharge Method: 6 kV
Air Discharge Method: 8 kV
(IEC/EN61000-4-2 Level 3)
Interface specifications
USB (Type A)
Conforms to USB 2.0 (Type A) x 1
Power supply voltage: 5 Vdc ±5 %
Output Current: 500 mA
Communication distance: 5 m [16.4 ft.]
USB (mini-B)
Conforms to USB 2.0 (mini-B) x 1, Communication Distance: 5 m [16.4 ft]

1When using the Display Module with the Power Box, you can connect only one of each type of USB device, such as one USB flash drive, one transfer cable, or one barcode reader. If you connect multiple devices that are the same type, only the first device will work.

Wireless LAN specifications
Frequency bandwidth
2.4 GHz
Channel bandwidth
20 MHz
Access Point mode: 1 to 11 ch Client mode: North America US: 1 to 11 ch Japan JP: 1 to 13 ch Europe EU: 1 to 13 ch Korea KR: 1 to 13 ch China CN: 1 to 13 ch Taiwan TW: 1 to 11 ch*2
Transmission speed
IEEE802.11b: max 11 Mbps
IEEE802.11g: max 54 Mbps
IEEE802.11n: max 72.2 Mbps
Transmission distance
The maximum 30 meters. (Distant varies depending on application software or use environment.)
Action mode
Client mode / Access Point mode
Communication mode
Network authentication
Open, WPA-Personal, WPA2-Personal
Data encryption
WEP (128 bit) (Open) AUTO/TKIP (WPA-Personal) AES (WPA2-Personal)*3
Maximum client connections
Connection angle and distance
Only the display side is connectable. The enabled connectivity angle and distance depend on your operating environment, applications to be used, and a communication target device. Be sure to conduct operation check including directionality in your operating environment before use.

1For the Wireless LAN, please use in a combination with the Open Box module. Do not use wireless communication to control machinery. Wireless communication system design must take into account the possibility of communication interference.

2In Access Point mode, IEEE802.11d is not supported.
In Client mode, if the surrounding access points do not support IEEE802.11d, channels are limited from 1 to 11 ch.

3In Access Point mode, WEP is not supported.

Structural specifications
Functional grounding: Grounding resistance of 100 Ω, 2 mm2 (AWG 14) or thicker wire, or your country’s applicable standard (same for FG and SG terminals).
Cooling method
Natural air circulation
When using a factory-installed front USB cover: IP65F, IP67F, Type 1
When using a front USB cover as an option: IP66F, IP67F, Type 1, Type 4X (indoor use only)/13
NOTE: The option is a front USB cover with screw manufactured by Pro-face (Model Number PFXZCDCVUS1).
External dimensions
W315 x H241 x D67 mm [W12.4 x H9.49 x D2.64 in.]
Panel cut-out dimensions
W301.5 x H227.5 mm [W11.87 x H8.96 in.]
Panel thickness area: 1.6 to 5 mm [0.06 to 0.2 in.]
3.2 kg [7.1 lb] or less*3

1The front face of the unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the unit's level of resistance is equivalent to these standards, oils that should have no effect on the unit can possibly harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the unit for long periods of time. If the unit's front face protection sheet becomes peeled off, these conditions can lead to the ingress of oil into the unit and separate protection measures are suggested. Also, if non-approved oils are present, it may cause deformation or corrosion of the front panel's plastic cover. Therefore, prior to installing the unit, be sure to confirm the type of conditions that will be present in the unit's operating environment. If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of the protection cannot be guaranteed. To maintain the original protection level, be sure to replace the installation gasket regularly.

2For dimensional tolerance, everything +1/-0 mm [+0.04/-0 in.] and R in angle are below R3 [R0.12 in.]. Even if the installation wall thickness is within the recommended range for the "Panel Cut Dimensions", depending on wall's material, size, and installation location of GP unit and other devices, the installation wall could warp. To prevent warping, the installation surface may need to be strengthened.

3Display module only.

External dimensions

Display module and box module combination


Panel cut-out dimensions


301.5 (+1/-0) mm
[11.87 (+0.04/-0)] in.
227.5 (+1/-0) mm
[8.96 (+0.04/-0)] in.
1.6 to 5 mm
[0.06 to 0.2] in.
External dimensions with cable


(Image of Open Box)

*1Rotation area of the fastener

*2Pitch of center of installation fastener screws