PFXLM4301TADAC

제품 기본 정보
제품 카테고리
HMI+Control
시리즈
LT4000M Series
화면 사이즈
5"
Model
PFXLM4301TADAC
글로벌 코드
PFXLM4301TADAC
제품 특징
5.7" DC AIO (Source) Type
판매 상태
판매중
수리 가능 여부
- (Maintenance service is not available. Replace with a new unit.)
디스플레이 표시 사양
디스플레이 타입
TFT 全彩 LCD
표시 사이즈
5.7"
해상도
320 x 240 像素 (QVGA)
유효 표시 사이즈
W115.2 x H86.4 mm [W4.54 x H3.40 in.]
표시 색상
65,536色
백라이트
White LED, Non-exchangeable, LED ON / OFF control, adjustable screen saver activation time
조도 조정
16 階 (可由觸控面板調整)
터치 패널 타입
電阻式薄膜(類比)
터치 패널 수명
1百萬次以上
표시 언어 종류
日語、ASCII、簡體中文、繁體中文、韓語、俄語、泰語*1
표시 문자 사이즈
8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixel fonts
표시 문자 확대율
Width can be expanded 1 to 8 times. Height can be expanded 1/2 and 1 to 8 times.
8 x 8 dots
40 字 x 30 列
8 x 16 dots
40 字 x 15 列
16 x 16 dots
20 字 x 15 列
32 x 32 dots
10 字 x 7 列

1대응하는 폰트 혹은 문자 코드 등에 대한 자세한 내용은, GP-Pro EX 레퍼런스 매뉴얼을 확인하여 주십시오.

전기 사양
정격 전압
24 Vdc
허용 전압 범위
20 to 28.8 Vdc
순간 정전 허용 시간 범위
在20.4 Vdc時10 ms以下
소비 전력
13 W以下
돌입 전류
28.8 Vdc: 30 A以下
절연내력
500 Vdc for 1 minute
절연저항
500 Vdc, 10 MΩ 以上
환경 사양
해외 안전 규격
CE, C-Tick, EAC, KC, UL,cUL (508) Listed, ANSI/CSA (UL508+1604) Listed, Marine DNV-GL
사용 환경 온도
Horizontal installation: 0 to 50 °C [32 to 122 °F]
Vertical installation: 0 to 40 °C [32 to 104 °F]
보관 온도
-20 至 60°C (-4 至 140°F)
사용 환경 온도
5 至 85 % RH (濕球溫度: 最高39 °C [102.2 °F] - 非凝結環境)
보관 습도
5 至 85 % RH (濕球溫度: 最高39 °C [102.2 °F] - 非凝結環境)
먼지
0.1 mg/m3 (10-7 oz/ft3) 以下 (非傳導等級)
오염도
適用於汙染程度 2 的環境
부식성 가스
非腐蝕性氣體的環境
대기압 (사용 고도)
800 至 1,114 hPa (海平線上2,000 m [6,561 ft.]以下)
내진동성
[Mounted on a DIN rail]
3.5 mm [0.138 in.] fixed amplitude from 5 to 8.4 Hz
9.8 m/s2 (1 gn) fixed acceleration from 8.4 to 150 Hz

[Mounted on a panel]
3.5 mm [0.138 in.] fixed amplitude from 5 to 8.6 Hz
9.8 m/s2 (1 gn) fixed acceleration from 8.6 to 150 Hz

[Vibration immunity (operating)]
IEC 61131-2
내충격성
[Mounted on a DIN rail] 147 m/s2 (15 gn) for a duration of 11 ms
[Mounted on a panel] 147 m/s2 (15 gn) for a duration of 6 ms
내소음성 (Fast Transient Burst Noise)
Power lines:2 kV
Digital I/O:1 kV
Relay outputs:2 kV
Ethernet line:1kV
COM line:1 kV
CAN line:1 kV
내정전기방전
6 kV 接觸放電、8 kV 空氣放電
표준 준거
IEC61131-2
보관 고도
0~10,000m
동작 고도
0~2,000m
보호도 (IEC61131-2)
IP20 with protective covers in place
방사성무선 주파수범위(IEC/EN 61000-4-3)
10V/m(80MHz~3GHz)
서지 내성(IEC/EN 61000-4-5)
[Power supply] CM: 1 kV, DM: 0.5 kV
[Digital I/O] CM: 1 kV, DM: 0.5 kV
[Shielded cable] 1 kV

CM = common drive
DM = differential drive
무선주파 전자계전도(IEC/EN 61000-4-6)
10Veff(0.15~80MHz)
단자 잡음(EN 55011 (IEC/CISPR11))
[150 to 500 kHz] quasi peak 79 dBμV
[500 kHz to 30 MHz] quasi peak 73 dBμV
전계 강도(EN 55011 (IEC/CISPR11))
[30 to 230 MHz] quasi peak 10 m @40 dBμV/m
[230 MHz to 1 GHz] quasi peak 10 m @47 dBμV/m
메모리
어플리케이션 메모리
FLASH EPROM 16 MB (includes screen editing program and extended logic program)*1
백업 메모리
nvSRAM 128 KB (Rechargeable lithium battery for data backup)
로직 프로그램 영역
FLASH EPROM 132 KB (等同於15,000 個 steps)*2
변수 영역
nvSRAM 64 KB (rechargeable lithium battery for data backup)
폰트 영역
FLASH EPROM 8 MB (when limit exceeded, uses application memory)

1유저 사용 가능 용량입니다.

2소프트웨어를 통해 최대 60,000 개의 화면까지 전환 가능합니다. 단, 어플리케이션 메모리 (화면 데이터) 용량이 1MB 줄어들게 됩니다.

인터페이스 사양
시리얼 (COM1)
RS-232C / 485 x 1
RS-232C(커넥터 타입 : RJ45, 절연 : x, 최대 전송 속도 : 115,200bps, 케이블 타입 : 실드 케이블, 케이블 최대 길이 15m, RS-232C용 DC5V전원: x )
RS-485 (커넥터 타입:RJ45, 절연 : x, 최대 전송 속도 : 300~115,200bps, 케이블 타입 : 실드 케이블, 케이블 최대 길이 : 200m, Polarization 저항 : LT를 복수 접속 할 경우, 소프트웨어로 설정이 필요합니다. 자세한 내용은 "GP-Pro EX 기기 접속 매뉴얼"을 확인하여 주시기 바랍니다. RS-485용 DC5V전원 : x)
*1
USB Type A
符合USB 2.0 (Type A) x 1
電源輸入電壓: 5 Vdc ±5 %
輸出電流: 500 mA以下
傳輸距離: 5 m [16.4 ft.]以下
이더넷
IEEE802.3 compliant Ethernet x 1
(Connector type: RJ45, Driver: 10 M half duplex (auto negotiation) / 100 M full duplex (auto negotiation), Cable type: Shielded, Automatic cross-over detection: Yes)
CANopen (Master)
CAN-CiA (ISO 11898-2:2002 Part 2), Connector: D-sub9 (pin)
Control
DIO:12點標準輸入(包含2點快速輸入) 6點標準輸出, 2點快速輸出 AIO:2ch類比輸入(13-bit)和2ch類比輸入(16-bit)熱電偶 2ch類比輸出(12-bit)

1RS-485에 대해서는 2선방식의 접속을 기본으로 하고 있습니다. 4선 방식이더라도, 접속 기기가 2선 방식을 지원하고 있는 경우, 송신 + 수신 + 과 송신 - 수신-을 각각 단락하여 접속시키는 경우가 있으므로, 자세한 내용은 접속 매뉴얼을 참조하여 주시기 바랍니다.

설치 사양
냉각 방식
自然氣流
보호 구조
NEMA#250 TYPE 4X (室內,安裝於外殼內)
顯示器模組: IP65F (IEC60529)
後裝模組: IP20 (IEC60529)
질량
0.8 kg以下
디지털 입력의 특성
정격 전류
5mA
돌입치(전압)
DC30V
돌입치 (전류)
6.29 mA max.
입력 임피던스
4.9 kΩ
입력 타입
Source
정격 전압
DC24V
최대 허용 전압
DC28.8V
입력제한치 (ON전압)
15 Vdc or more (15 to 28.8 Vdc)
입력제한치 (OFF전압)
5 Vdc以下(0 至 5 Vdc)
입력제한치 (ON전류)
2.5 mA or more
입력제한치 (OFF전류)
1.0 mA以下
절연 방식
Photo coupler Isolation
절연 (내부회로간)
DC500V
Filter
0.5 ms x N (N is 0 to 63)
IEC61131-2 edition 3 type
Type 1
호환성
Supports 2 wire and 3 wire sensors
케이블 종류 및 길이
Shielded: Maximum 100 m (328 ft)
Non-shielded: 50 m (164 ft)
단자대
Type: 3.5 mm (0.137 in.) pitch
Terminal blocks are removable.
입력 병렬 접속
아니오
고속 카운터 및 펄스 캐치 입력 사양
정격전류 (전압)
DC24V
정격전류 (전압)
7.83mA
돌입치(전압)
DC30V
돌입치 (전류)
9.99mA
입력 임피던스
3.2kΩ
입력 타입
Source
정격 전압
DC24V
최대 허용 전압
DC28.8V
입력제한치 (ON전압)
15 Vdc or more
입력제한치 (OFF전압)
5 Vdc以下
입력제한치 (ON전류)
|5 mA or more
입력제한치 (OFF전류)
1.5 mA以下
절연 방식
Photo coupler Isolation
절연 (내부회로간)
DC500V
Filter
없음、 4μs、40μs
IEC61131-2 edition 3 type
Type 1
호환성
Supports 2 wire and 3 wire sensors
케이블 (타입)
Shielded cable
케이블 (길이)
Maximum 10 m (33 ft)
단자대
Type: 3.5 mm (0.137 in.) pitch
Terminal blocks are removable.
최대주파수
- 100 kHz is the maximum frequency for Single-phase
- 50 kHz is the maximum frequency for 2-phase
- Duty Rate: 45 to 55%
페이즈 카운팅 모드
- Single phase
- 2 Phase x 2
- 2 Phase x 4
- 2 Phase x 2 Reverse
- 2 Phase x 4 Reverse
응답시간 (메이커)
1ms
응답시간 (프리로드)
1ms
응답시간 (프리스트롭)
1ms
응답 시간 [싱크로 출력]
2ms
입력 병렬 접속
없음
트랜지스터 출력 사양
정격 전압
DC24V
출력 범위
DC19.2~28.8V
출력 타입
Source
정격 전류
0.3 A/point, 1.8 A/common
잔류 전압
1.5 Vdc or less for I= 0.1A
Delay
Off to on (0.3 A load): 1.1ms
On to off (0.3 A load): 2ms
NOTE: The delay is not including the cable delay.
절연 방식
Photo coupler Isolation
절연 (내부회로간)
DC500V
최소 저항 부하
80Ω at 24 Vdc
케이블 길이
无屏蔽:150m
쇼트에 대한 보호
없음
단자대
Type: 3.5 mm (0.137 in.) pitch
Terminal blocks are removable.
Note1
Note: Refer to LT4201TM/4301TM Hardware Manual about Protecting Outputs from Inductive Load Damage for additional information on this topic.
Note2
Caution: Q0 and Q1 circuits are push-pull circuits. The following is the operation of the push-pull circuit at the Sink Output and the Source Output.
Sink Output: +24(V) is output to terminal Q0, Q1 when the logic for Q0, Q1 is off
Source Output: 0(V) is output to terminal Q0, Q1 when the logic for Q0, Q1 is off

Standard Output terminals Q2 or later are common open collector outputs.
Do not connect Fast Output terminals Q0, Q1 and Standard Output terminals Q2 or later. It will short.
Note3
Type: 3.5 mm (0.137 in.) pitch
Terminal blocks are removable.
펄스 출력, PWM 출력 , 고속 카운터 일치 출력 사양
출력 타입
Source
정격 전압
DC24V
전원 입력 범위
DC19.2~28.8V
역전원 보호
펄스 출력/ PWM출력 전류
50 mA/point, 100 mA/common
오리지널 입력에 대한 응답 시간
2ms
절연 저항 [고속 출력과 내부 회로 사이]
10 MΩ or more
절연 저항 [전원 포트와 보호 접지 (PE)=DC500V 사이]
10 MΩ or more
잔류 전압 [for I = 0, 1 A]
1.5 Vdc以下
Delay
Off to on (50 mA load): 1.1 ms
On to off (50 mA load): 1.1 ms
NOTE: The delay is not including the cable delay.
최소 로드 임피던스
80&Omega
최대 펄스 출력 주파수
50KHz
최대 PWM 출력 주파수
65kHz
Accuracy Pulse Output/ PWM Output [10 to 100 Hz]
Accuracy: 0.1%
Duty: 0 to 100 %
Accuracy Pulse Output/ PWM Output [10 to 1000 Hz]
Accuracy: 1%
Duty: 1 to 99 %
Accuracy Pulse Output/ PWM Output [1.001 to 20kHz]
Accuracy: 5%
Duty: 5 to 95 %
Accuracy Pulse Output/ PWM Output [20.001 to 45kHz]
Accuracy: 10%
Duty: 10 to 90 %
Accuracy Pulse Output/ PWM Output [45.001 to 65 kHz]
Accuracy: 15%
Duty: 15 to 85 %
듀티 비율 범위
1~99%
케이블 (타입)
Shielded, including 24 Vdc power supply
케이블 (길이)
Maximum 5 m (16 ft)
단자대
Type: 3.5 mm (0.137 in.) pitch
Terminal blocks are removable.
Note1
NOTE: When using the acceleration/deceleration pulse output, there is a 1% maximum error for the frequency.
Note2
Caution: Q0 and Q1 circuits are push-pull circuits. The following is the operation of the push-pull circuit at the Sink Output and the Source Output.
Sink Output: +24(V) is output to terminal Q0, Q1 when the logic for Q0, Q1 is off
Source Output: 0(V) is output to terminal Q0, Q1 when the logic for Q0, Q1 is off

Standard Output terminals Q2 or later are common open collector outputs.
Do not connect Fast Output terminals Q0, Q1 and Standard Output terminals Q2 or later. It will short.
Note3
Type: 3.5 mm (0.137 in.) pitch
Terminal blocks are removable.
Analog input specifications
Number of maximum input
2
입력 타입
Single-ended
Input range
01|[Voltage input] -10 to 10 Vdc / 0 to 10 Vdc
[Current input] 0 to 20 mA / 4 to 20 mA
입력 임피던스
[Voltage input] 1 MΩ or more
[Current input] 250 ± 0.11% Ω
Sample duration time
10 ms per channel + 1 scan time
Total input system transfer time
20 ms + 1 scan time
Input tolerance
01|[Maximum deviation] ± 2.5 % of the full scale
[Maximum deviation at 25 °C [77 °F] without electromagnetic disturbance] ± 1 % of the full scale
Digital resolution
13 bits
Temperature drift
± 0.06 % of the full scale
Common mode characteristics
80db
Cross talk
60db
Non-linearity
± 0.4 % of full scale
Input value of LSB
[Voltage input] 5 mV
[Current input] 10 µA
Maximum allowed overload (no damages)
[Voltage input] ± 30 Vdc (less than 5 minutes) / ± 15 Vdc (No damage)
[Current input] ± 30 mA dc
절연내력
Photo coupler between input and internal circuit
케이블 (타입)
Shielded cable
케이블 (길이)
Must be less than 3 m for IEC61131-2 conformance.
Maximum transmission distance is 10m.
단자대
Type: 3.5 mm (0.137 in.) pitch
Terminal blocks are removable.
Isolation (photocoupler) [External input]
Photo coupler Isolation
Isolation (Photocoupler)[Between channels]
Non-isolated
Temperature input (temperature probes) specifications
Input sensor type
Pt100 / Pt1000 / Ni100 / Ni1000
Input temperature range
Pt100/Pt1000:-200 to 600℃, Ni100/Ni1000:-50~200℃
Measuring current [Pt100/Ni100]
1.12 mA ± 3.5 %
Measuring current [Pt1000/Ni1000]
0.242 µA ± 3.5 %.
입력 임피던스
Typically 10 M&Omega
Sample duration time
10 ms + 1 cycle time
Wiring type
2-wire or 3-wire connection configured by software for all inputs
Conversion mode
Sigma delta type
Input filter
Low pass
해상도 온도치
0.1℃
Detection type
Open circuit (detection on each channel)
Input tolerance [Maximum deviation at 25°C (77°F) without electromagnetic disturbance]
± 5 °C [41 °F]*1
Input tolerance [Maximum deviation at 25 to 50°C (77 to 122°F)]
Pt type: ± 5.6 °C [42.08 °F]
Ni type: ± 5.2 °C [41.36 °F]
Temperature drift
30 ppm/°C
Digital resolution
16 bits
Rejection in differential mode (50/60 Hz)
Typically 60 dB
Common mode rejection (50/60 Hz)
Typically 80 dB
Isolation Method
Photo coupler Isolation
Permitted input signal
± 5 Vdc max.
케이블 길이 [Pt100/Ni100]
20 Ω 以下
케이블 길이[Pt1000/Ni1000]
200 Ω 以下
단자대
Type: 3.5 mm (0.137 in.) pitch
Terminal blocks are removable.
Noise resistance - cable
Shielded cable is necessary.

1Excluding errors caused by the wiring.

Temperature input (thermocouple) specifications
Input sensor type
Thermocouple
입력 타입의 범위
J(-200~760℃)、K(-240~1,370℃)、R(0~1,600℃)、B(200~1,800℃)、S(0~1,600℃)、T(-200~400℃)、E(-200~900℃)、N(-200~1,300℃)*1
입력 임피던스
Typically 10 MΩ
Sample duration time
10 ms + 1 cycle time
Conversion mode
Sigma delta type
Digital resolution
16 bits
Input filter
Low pass
해상도 온도치
0.1 °C (0.18 °F)
Detection type
Open circuit (detection on each channel)
Input tolerance [Maximum deviation at 25°C (77°F) without electromagnetic disturbance]
0.2 % of the full scale, plus standard point of compensation precision at ±6 °C [42.8 °F] .
Input tolerance [Maximum deviation]
0.28 % of full scale range
Temperature drift
30 ppm/°C
Input tolerance - terminal temperature compensation
±5 °C [41 °F] after 10 min.
Cold junction compensation in the temperature range (0 to 50°C (122°F))
Internal cold junction error: ±6 °C [42.8 °F]
after operating 45 minutes.
Rejection in differential mode (50/60 Hz)
Typically 60 dB
Common mode rejection (50/60 Hz)
Typically 80 dB
Isolation Method
Photo coupler Isolation
Permitted input signal
±5 Vdc max.
Warm up time
45 minutes
단자대
Type: 3.5 mm (0.137 in.) pitch
Terminal blocks are removable.
Noise resistance - cable
Shielded cable is necessary.

1Temperature measurement on PCB at terminal block for cold junction compensation.

Analog output specifications
Maximum number of outputs
2
출력 범위
[Voltage Output] -10 to 10 Vdc / 0 to 10 Vdc
[Current Output] 0 to 20 mA / 4 to 20 mA
Load impedance
[Voltage Output] 2 kΩ or more
[Current Output] 300 Ω or more
Application load type
Resistive load
Setting time
10ms
Total input system transfer time
10 ms + 1 scan time
Output tolerance [Maximum deviation at 25°C (77°F) without electromagnetic disturbance]
±1 % of the full scale
Output tolerance [Maximum deviation]
± 2.5% of the full scale
Digital resolution
12 bits
Temperature drift
± 0.06 % of the full scale
Output ripple
± 50 mV
Cross talk
60db
Non-linearity
± 0.5% of full scale
Output value of LSB
[Voltage Output] 6 mV
[Current Output] 12 µΑ
절연내력
Photo coupler between input and internal circuit
Output protection
Short circuit protection: Yes
Open circuit protection: Yes
Output behavior if input power supply is less than the power failed threshold
Set to 0
케이블 (타입)
Shielded cable
케이블 (길이)
Must be less than 3 m for IEC61131-2 conformance.
Maximum transmission distance is 10m.
단자대
Type: 3.5 mm (0.137 in.) pitch
Terminal blocks are removable.
Isolation (photocoupler) [External input]
Photo-coupler isolation
Isolation (Photocoupler)[Between channels]
Non-isolated
Terminal blocks
A1 (Signal Name , Group)
V0+ (Fast Output)
A2 (Signal Name , Group)
Q1 (Fast Output)
A3 (Signal Name , Group)
V1+ (Standard Output)
A4 (Signal Name , Group)
Q3 (Standard Output)
A5 (Signal Name , Group)
Q5(標準出力)
A6 (Signal Name , Group)
Q7 (Standard Output)
B1 (Signal Name , Group)
V0- (Fast Output)
B2 (Signal Name , Group)
Q0 (Fast Output)
B3 (Signal Name , Group)
V1- (Standard Output)
B4 (Signal Name , Group)
Q2 (Standard Output)
B5 (Signal Name , Group)
Q4 (Standard Output)
B6 (Signal Name , Group)
Q6 (Standard Output)
C1 (Signal Name , Group)
I0 (Fast Input / Standard Input)
C2 (Signal Name , Group)
I1 (Fast Input / Standard Input)
C3 (Signal Name , Group)
I3 (Fast Input / Standard Input)
C4 (Signal Name , Group)
I5 (Standard Input)
C5 (Signal Name , Group)
I7 (Standard Input)
C6 (Signal Name , Group)
I9 (Standard Input)
C7 (Signal Name , Group)
I11 (Standard Input)
C8 (Signal Name , Group)
MS0+ (Temperature Input)
C9 (Signal Name , Group)
EX0+ (Temperature Input)
C10 (Signal Name , Group)
MS1+ (Temperature Input)
C11 (Signal Name , Group)
EX1+ (Temperature Input)
C12 (Signal Name , Group)
IV0 (Analog Input)
C13 (Signal Name , Group)
IV1 (Analog Input)
C14 (Signal Name , Group)
IA1 (Analog Input)
C15 (Signal Name , Group)
U/I0 (Analog Output)
D1 (Signal Name , Group)
IC0 (Fast Input / Standard Input)
D2 (Signal Name , Group)
I2 (Standard Input)
D3 (Signal Name , Group)
IC1 (Standard Input)
D4 (Signal Name , Group)
I4 (Standard Input)
D5 (Signal Name , Group)
I6 (Standard Input)
D6 (Signal Name , Group)
I8 (Standard Input)
D7 (Signal Name , Group)
I10 (Standard Input)
D8 (Signal Name , Group)
MS0- (Temperature Input)
D9 (Signal Name , Group)
EX0- (Temperature Input)
D10 (Signal Name , Group)
MS1- (Temperature Input)
D11 (Signal Name , Group)
EX1- (Temperature Input)
D12 (Signal Name , Group)
AIC (Analog Input)
D13 (Signal Name , Group)
IA0 (Analog Input)
D14 (Signal Name , Group)
AOC (Analog Output)
D15 (Signal Name , Group)
U/I1 (Analog Output)
외관도
외형 도면
 
lt4301_dimension.gif
패널 컷 사이즈
 
panel_cut.gif
 
* Without the tee option, the display module supports a rotating torque of 2.5 N•m (22.12 lbin).