PFXSP5490WAD / PFXSP5490WADF0H

產品基本資訊
產品類型 
HMI
系列 
SP5000X Series
顯示器尺寸 
7" Wide
型號 
PFXSP5490WAD
全球碼 
PFXSP5490WAD
產品主要特色 
7" Wide DC
可否維修 
維修收件期內,可維修
顯示器規格
顯示類型 
TFT 全彩 LCD (超亮度)
顯示尺寸 
7"寬螢幕
解析度 
800 x 480 像素 (WVGA)
有效可視面積 
W152.4 x H91.4 mm [W6.0 x H3.6 in.]
顯示顏色 
262,144 colors
背光 
白色 LED (用戶無法自行更換。需更換時,請與您的代理商聯絡。)
背光使用年限 
50,000小時以上(在25 °C [77 °F]下連續工作 - 亮度下降至原來的50%)
亮度控制 
0 至 100 (可由觸控面板或軟體調整)
Brightness 
1000 cd/m2 (typ.)
觸控面板類型 
電阻式薄膜(類比)
觸控面板解析度 
1,024 x 1,024
觸控面板使用年限 
1百萬次以上
電源規格
輸入電壓 
12 至 24 Vdc
額定電壓 
10.8 to 28.8 Vdc
允許的壓降 
12 Vdc: 1.25 ms以下
24 Vdc: 5 ms以下
耗電量 
Max. 29 W
When power is not supplied to external devices: 17.5 W or less
Backlight OFF (Stand-by mode): 12.5 W or less
Backlight adjusted (20%): 15 W or less*1
湧入電流 
30 A以下
耐雜訊 
雜訊電壓:1,000 Vp-p
脈衝寬度:1 µs
上升時間:1 ns
(雜訊模擬器測得)
耐壓特性 
1,000 Vac for 1 minute (between power terminal and FG terminals), leakage current: 20 mA or less
絕緣電阻 
500 Vdc, 10 MΩ 以上

1The power consumption is the sum of the power consumption of Box Module and Display Module.

環境規格
國際安全標準 
ce.gifctick.gifeac.gifex.gifkc.giful508.giful508ansi.gifIECEx.gif
周圍空氣溫度 
-30 to 65 °C [-22 to 149 °F]
When installing and wiring: -5 to 65 °C [23 to 149 °F]
儲存溫度 
-30 to +70 °C [-22 to 158 °F]
環境濕度 
10 至 90 % RH (濕球溫度: 最高39 °C [102.2 °F] - 非凝結環境)
儲存濕度 
10 至 90 % RH (濕球溫度: 最高39 °C [102.2 °F] - 非凝結環境)
灰塵 
0.1 mg/m3 (10-7 oz/ft3) or less (free of conductive dust particles on all surfaces other than the front face)
汙染程度 
3 for front face, 2 for other sides
腐蝕性氣體 
Free of corrosive gases
Harsh environment model (Model numbers ending with "F0H") : IEC/EN 60721-3-3 Class 3C3
耐氣壓震動(高度範圍) 
800 to 1,114 hPa (2,000 m [6,561 ft.] or lower)
UV resistance (front side) 
Cutoff: 99% or more (380 nm)
耐震動 
2G, IEC 60068-2-6 compliant, 5 to 9 Hz Single amplitude 7 mm [0.28 in.], 9 to 150 Hz Fixed acceleration: 19.6 m/s2, X, Y, Z directions for 10 cycles (approximately 100 minutes), IEC 61373: 1999 (Category 1, Class B), 5≤f≤150 Hz (weight < 500 kg: f1=5 Hz, f2=150 Hz) acceleration: Up and down: 7.90 m/s2, Right and left: 3.50 m/s2, Back and forward: 5.50 m/s2
耐衝擊 
40G, IEC 60068-2-27 compliant 392 m/s2, 11 ms, X, Y, Z directions for 3 times
抗靜電放電力 
接觸放電法:6 kV
空氣放電法: 8 kV (IEC/EN61000-4-2 第3級)
結構規格
接地 
功能接地:接地電阻 100Ω、電線厚度 2mm² (AWG14)或以上,或符合當地國家標準(同樣適用於 FG 及 SG 端子)。
冷卻方法 
自然氣流
結構規格 
IP66F, IP67F, Type 4X (indoor and outdoor use), Type 12, Type13
* on the front panel when properly installed in an enclosure.*2
外部尺寸 
W203.6 x H148.6 x D37 mm [W8.02 x H5.85 x D1.45 in.]
開孔尺寸 
W190 x H135 mm [W7.48 x H5.31 in.]
面板厚度: 1.6 至 5 mm [0.06 至 0.2 in.]*3
重量 
1.3 kg [2.87 lb] or less
Front bezel 
Aluminum die-cast
Stainless steel

2The front face of the unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the unit's level of resistance is equivalent to these standards, oils that should have no effect on the unit can possibly harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the unit for long periods of time. If the unit's front face protection sheet becomes peeled off, these conditions can lead to the ingress of oil into the unit and separate protection measures are suggested. Also, if non-approved oils are present, it may cause deformation or corrosion of the front panel's plastic cover. Therefore, prior to installing the unit, be sure to confirm the type of conditions that will be present in the unit's operating environment. If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of the protection cannot be guaranteed. To maintain the original protection level, be sure to replace the installation gasket regularly.
Check the model number and product version (PV) on the product label. If the product version is “PV: 01” and only with one of the following model numbers, the protection level is IP66F.
Model number: PFXSP5490WAD, PFXSP5690WAD

3尺寸誤差值在 +1/-0 mm (+0.04/-0 in.),R角誤差值低於 R3 (R0.12 in.)。即使安裝外殼厚度在"開孔尺寸"的建議範圍內,由於外殼材質、尺寸、和產品安裝處的不同, 外殼仍有可能彎曲。要避免彎曲,請強化安裝面。

產品尺寸
外部尺寸 
Display module and box module combination
 
開孔尺寸 
A B C
190 (+1/-0) mm
[7.48 (+0.04/-0) in.]
135 (+1/-0) mm
[5.31 (+0.04/-0) in.]
1.6 to 5 mm
[0.06 to 0.2 in.]
包含接線的外部尺寸 

*1: Rotation area of the fastener
*2: Pitch of center of installation fastener screws