**************************   FP5000 Driver & Utility   *************************
                                                                   February 2019
                                                              Schneider Electric

Thank you for using FP5000.
These drivers and utilities are required for communication between FP5000 and 
the host, and adjustment of the screen display. 

Table of Contents
 (0) Introduction
 (1) Version
 (2) Supported Operating Systems
 (3) Limitations
  3-1  System configuration
  3-2  Drivers
  3-3  Utility (Launcher)
 (4) Manuals
 (5) Fixed Defects

Contents
================================================================================
 (0) Introduction
  Communication driver   : This driver enables communication between FP5000 and
                           the utilities
  Utility                : The Launcher is a utility that displays icons to
                           configure settings on FP5000 with convenient touch
                           operation.

 (1) Version
  Communication driver      : Ver.1.0.3.0
  Utility                   : Ver.1.00.0015

 (2) Supported Operating Systems
    These drivers and utilities support to the following operating system.
    - Windows(R) 7 Service Pack 1 / Professional / Enterprise / Ultimate (32bit / 64bit)
    - Windows(R) 8.1 Pro / Enterprise (32bit / 64bit)
    - Windows(R) 10 Home / Pro / Enterprise (32bit / 64bit)
    - Windows(R) Embedded Standard 7 for Pro-face products (32bit / 64bit)
    - Windows(R) Embedded 8.1 Industry Pro / Enterprise (32bit / 64bit)
    - Windows(R) 10 IoT Enterprise 2016 LTSB (32bit / 64bit)

    These drivers and utilities do not support the following operating system.
    Please use the ver.1.00.0013.
    - Windows(R) XP 32-bit
    - Windows(R) Embedded Standard 2009 for Pro-face products

 (3) Limitations
  3-1  System configuration
      <Display/Touch Input>
      - FP5000 supports only single connection to a host PC.
        Do not connect more than two FP5000 to a host PC.

  3-2  Drivers
      <Driver's installation>
      - Before installing this driver on Windows(R) 7, install
        Kernel-Mode Driver Framework version 1.11
        from Windows Update.
      <Display/Touch Input>
      - Do not frequently plug in/out USB and DVI cables while the power is on. 
        Check the connection before turning the power on.

  3-3  Utility (Launcher)
      <.NET Framework 4.0>
      - Before using this program on Windows(R) 7, install
        .NET Framework 4.0 patch of (KB2840628v2) in the following website.
        URL : http://www.microsoft.com/en-us/download/details.aspx?id=39509
      <T/P Calibration>
        When performing T/P Calibration in the extended display mode, configure 
        Launcher Set to display the Launcher on the FP5000 side.
      <Display>
        Adjusting contrast and the black level of the display in graphic property 
        on the host PC.
      <Tablet PC>
        Please enable "Tablet PC Input Service" on the host PC.
        Before using the FP5000.
      <Firmware update>
        When update firmware of FP5000 on Windows(R) 10, the messages appearing 
        on the update tool may not show properly.
      <Launcher>
        If the DVI cable gets unplugged while the Launcher is displayed on the FP5000, 
        the Launcher will move to another display.
      <Front USB>
        After the setup is done, FP5000 does not automatically restart. To update the 
        settings, restart the FP5000 manually.

 (4) Manuals
   For more information about the drivers and utility, refer to FP5000 Series 
   User Manual. You can download the manual from our support site.
   (http://www.pro-face.com/trans/en/manual/1001.html)

 (5) Fixed Defects
   Utility: Ver.1.00.0008
      Drawing area of Launcher was changed not to never covers task bar.
      Firmware update function was added to make the drivers automatically 
      installed at the same time as the Utility is installed.
   Utility: Ver.1.00.0009
      Touch panel calibration can be canceled.
      Fixed the issue that a screensaver run in power saving mode during 
      remote access. Fixed the issue that communication between FP5000 and 
      a host PC failed when Windows logoff and logon are performed repeatedly.
      Fixed the memory leak.
   Utility: Ver.1.00.0010
      Fixed the following issues occurred when FP5000 only is restarted.
      - Click Buzzer does not work
      - Launcher does not start
      - Backlight becomes dark when auto brightness is enabled
      - Front LED shows orange blink forever when auto brightness is enabled
   Utility: Ver.1.00.0011
      Supports mouse-compatible operation with the Mouse Emulation Software (DMT-DD)
      in Windows(R) 7 and 8.
      (However, it does not support the extended desktop mode.)
   Utility: Ver.1.00.0012
      Fix the following issues occurred when connecting to Windows(R) XP.
      - Touch operation gets disabled when the angle of the display is 90 or 270 degrees.
   Utility: Ver.1.00.0013
      Changed the method to start Launcher with touch operation on Windows(R) 7, 8.
      The 1st touch point is always left top of screen when rotate the screen.
   Utility: Ver.1.00.0014
      Windows(R) 10 is supported.
      Windows(R) XP is out of support.
   Utility: Ver.1.00.0015
      Changed Launcher Set to show only one FP5000 target.

================================================================================
Copyright (C) 2019 Schneider Electric Japan Holdings Ltd. All Rights Reserved.
Microsoft(R) and Windows(R) are registered trademarks of Microsoft Corporation in 
the United States and/or other countries.
Product names used in this document may be the registered trademarks owned by the 
respective proprietors.
No part of this document may be used or reproduced without permission.
****************************  End of Release Note  *****************************
